| Citation: | LI Xin, LI Shijin, LE Chen, FAN Zimin, CAI Jianing. Preparation of ultra-fine iron powders by water-gas atomization and its application on laser welding saw blades[J]. Diamond & Abrasives Engineering, 2023, 43(3): 305-312. doi: 10.13394/j.cnki.jgszz.2022.0103
|
Ultra-fine iron powder was prepared by water-gas atomization process. The physical properties and the micro morphologies of the ultra-fine iron powder, the reduced iron powder and the carbonyl iron powder were compared. The sintered blocks of three kinds of iron powders were prepared under a certain hot pressing process, and their fracture morphologies and mechanical properties were investigated. At the same time, the three kinds of iron powders were applied to the transition layer of laser welding saw blades under certain welding conditions to investigate their welding performances. The results show that the ultra-fine iron powder prepared by water-gas atomization process has fine particles, lower oxygen content, higher purity and sphericity, and better sintering activity. There are obvious dimple structures on the fracture surface of the sintered block, which has higher toughness and can achieve greater density, hardness and bending strength at lower sintering temperature. When the ultra-fine iron powder is applied to the transition layer of the laser welding saw blade, the welding strength of the saw blade is much higher than 600 MPa specified in the EU EN13236 standard. When the sintering pressure is 35 MPa, the sintering temperature is 810 ℃ and the holding time is 3 min, the cutter head is made, and then the saw blade is made with this cutter head. The maximum welding strength of the saw blade is 1 900 MPa.
| [1] |
王志刚. 激光焊金刚石圆锯片的无损检测 [J]. 金刚石与磨料磨具工程,2001(6):19-20. doi: 10.3969/j.issn.1006-852X.2001.06.006
WANG Zhigang. Non-damage measurement of laser weld diamond circular saw blade [J]. Diamond & Abrasives Engineering,2001(6):19-20. doi: 10.3969/j.issn.1006-852X.2001.06.006
|
| [2] |
罗锡裕, 徐燕军, 张广宁, 等. 金刚石锯片焊接部位的组织结构与力学性能 [J]. 粉末冶金工业,2016,26(6):1-7. doi: 10.13228/j.boyuan.issn1006-6543.20160108
LUO Xiyu, XU Yanjun, ZHANG Guangning, et al. Microstructure and mechanical properties of welding zones of diamond saw blade [J]. Powder Metallurgy Industry,2016,26(6):1-7. doi: 10.13228/j.boyuan.issn1006-6543.20160108
|
| [3] |
申思, 宋月清, 汪礼敏, 等. 一种激光焊接金刚石锯片过渡层用预合金粉末的性能研究 [J]. 金刚石与磨料磨具工程,2007(4):32-35. doi: 10.3969/j.issn.1006-852X.2007.04.009
SHEN Si, SONG Yueqing, WANG Limin, et al. Study on pre-alloyed powder used as backing powder in laser welding diamond tools [J]. Diamond & Abrasives Engineering,2007(4):32-35. doi: 10.3969/j.issn.1006-852X.2007.04.009
|
| [4] |
CESAR M G M M, MANTEL M J. Effect of the temperature and dew point of the decarburization process on the oxide subscale of a 3% silicon steel [J]. Journal of Magnetism and Magnetic Materials,2003,254/255:337-339. doi: 10.1016/S0304-8853(02)00836-3
|
| [5] |
李立波, 唐霞辉, 秦应雄, 等. 激光焊接金刚石工具过渡层预合金粉末研究 [J]. 金刚石与磨料磨具工程,2005(2):56-60. doi: 10.3969/j.issn.1006-852X.2005.02.017
LI Libo, TANG Xiahui, QIN Yingxiong, et al. Developing status of pre-alloyed backing powder used in laser welded diamond tools [J]. Diamond & Abrasives Engineering,2005(2):56-60. doi: 10.3969/j.issn.1006-852X.2005.02.017
|
| [6] |
向波, 谢志刚, 贺跃辉, 等. 激光焊接金刚石工具用铁钴预合金粉末的制备与性能 [J]. 机械工程材料,2007(10):55-57. doi: 10.3969/j.issn.1000-3738.2007.10.017
XIANG Bo, XIE Zhigang, HE Yuehui, et al. Preparation and performance of prealloyed powder for laser welding diamond tools [J]. Materials for Mechanical Engineering,2007(10):55-57. doi: 10.3969/j.issn.1000-3738.2007.10.017
|
| [7] |
杨海鲸, 朱晓云, 龙晋明, 等. 超细银粉制备方法的研究进展 [J]. 热加工工艺,2017,46(24):20-24. doi: 10.14158/j.cnki.1001-3814.2017.24.005
YANG Haijing, ZHU Xiaoyun, LONG Jinming, et al. Research progress of preparation methods of ultrafine silver powder [J]. Hot Working Technology,2017,46(24):20-24. doi: 10.14158/j.cnki.1001-3814.2017.24.005
|
| [8] |
朱杰, 宗伟, 李志, 等. 水气联合雾化法制备微细球形金属粉末 [J]. 材料研究与应用,2016,10(3):201-204. doi: 10.3969/j.issn.1673-9981.2016.03.010
ZHU Jie, ZONG Wei, LI Zhi, et al. Preparation of spherical fine metal powder by hybrid water-gas atomization [J]. Materials Research and Application,2016,10(3):201-204. doi: 10.3969/j.issn.1673-9981.2016.03.010
|
| [9] |
刘坤杰, 乐晨, 赵放, 等. 水气联合雾化法制备铁基预合金粉末及其在金刚石工具中的应用 [J]. 金刚石与磨料磨具工程,2018,38(2):32-36. doi: 10.13394/j.cnki.jgszz.2018.2.0007
LIU Kunjie, LE Chen, ZHAO Fang, et al. Preparation of iron-based pre-alloyed powders by water-gas atomization and its application in diamond tools [J]. Diamond & Abrasives Engineering,2018,38(2):32-36. doi: 10.13394/j.cnki.jgszz.2018.2.0007
|
| [10] |
马毅龙, 郭志猛, 罗骥, 等. 氧化物弥散强化铁粉在金刚石工具中的应用 [J]. 金刚石与磨料磨具工程,2011,31(5):84-87, 90. doi: 10.3969/j.issn.1006-852X.2011.05.019
MA Yilong, GUO Zhimeng, LUO Ji, et al. Application of ODS iron-powder in diamond tools [J]. Diamond & Abrasives Engineering,2011,31(5):84-87, 90. doi: 10.3969/j.issn.1006-852X.2011.05.019
|
| [11] |
章林, 吕元之, 邵健, 等. 粘结化铁基粉末的高速压制成形与烧结行为研究 [J]. 粉末冶金技术, 2012, 30(1): 57-62.
ZHANG Lin, LV Yuanzhi, SHAO Jian, et al. Study on high velocity compaction and sintering behaviour of bonding treated ferrous powder [J]. Powder Metallurgy Technology, 2012, 30(1): 57-62.
|
| [12] |
DAI H, WANG L, ZHANG J, et al. Iron based partially pre-alloyed powders as matrix materials for diamond tools [J]. Powder Metallurgy,2015,58(2):83-86. doi: 10.1179/0032589915Z.000000000220
|
| [13] |
安传锋, 何浩, 李益民, 等. C和Nb添加对金属注射成形420不锈钢组织及性能的影响 [J]. 广西科技大学学报,2018,29(2):63-69, 96. doi: 10.16375/j.cnki.cn45-1395/t.2018.02.010
AN Chuanfeng, HE Hao, LI Yimin, et al. Effect of carbon and Nb on sintering densification and mechanical properties of MIM 420 stainless steel [J]. Journal of Guangxi University of Science and Technology,2018,29(2):63-69, 96. doi: 10.16375/j.cnki.cn45-1395/t.2018.02.010
|
| [14] |
潘晓毅, 谢德龙, 林峰, 等. 激光焊接金刚石工具过渡层配方设计初步研究 [J]. 超硬材料工程,2018,30(4):11-15. doi: 10.3969/j.issn.1673-1433.2018.04.003
PAN Xiaoyi, XIE Delong, LIN Feng, et al. Preliminary study on the powder formula design of laser-welded diamond tool′s transition layer [J]. Superhard Material Engineering,2018,30(4):11-15. doi: 10.3969/j.issn.1673-1433.2018.04.003
|
| [15] |
ZHANG H T, XIAO C J, ZHU L Y, et al. Structure and mechanical properties of impregnated diamond cutting tools using Cu-based metal matrix [J]. Advanced Materials Research,2014,873:30-35.
|
| [16] |
王新月, 李松林, 刘向阳, 等. 添加Fe-Ni粉对Fe-4Ni-0.4C低合金钢组织与性能的影响 [J]. 粉末冶金材料科学与工程,2021,26(5):428-435. doi: 10.3969/j.issn.1673-0224.2021.05.006
WANG Xinyue, LI Songlin, LIU Xiangyang, et al. Effect of adding the Fe-Ni powder on the structure and properties of Fe-4Ni-0.4C low-alloy steel [J]. Materials Science and Engineering of Powder Metallurgy,2021,26(5):428-435. doi: 10.3969/j.issn.1673-0224.2021.05.006
|
| [17] |
蒙光海, 雷晓旭, 卢安军, 等. CuSn15和Fe对无压烧结金刚石工具胎体性能的影响 [J]. 粉末冶金技术,2015,33(2):105-110. doi: 10.3969/j.issn.1001-3784.2015.02.005
MENG Guanghai, LEI Xiaoxu, LU Anjun, et al. Effects of CuSn15 and Fe on the properties of pressureless sintered diamond tools matrix [J]. Powder Metallurgy Technology,2015,33(2):105-110. doi: 10.3969/j.issn.1001-3784.2015.02.005
|
Figures(9) / Tables(3)
Supported by:
Beijing Renhe Information Technology Co., Ltd.
Email Alerts
RSS
DownLoad:
